Month: October 2022
27Oct

Categories: Blog

If you have a truck, you know how important it is to keep your lug wrench on hand. A good lug wrench can make all the difference when changing a tire, especially if you are in the middle of nowhere and don’t have access to any other tools.

However, with so many different lug wrenches on the market, it can take time to determine which one is best for your vehicle. The first thing you should do before purchasing a new lug wrench is measure the size of your wheel lugs. This will help you determine what size of wrench will work best for your vehicle and allow you to purchase one that fits without having to return it.

Some things need to be considered when looking for a new lug wrench, such as durability and materials used in construction. You want something that will last but will be relatively inexpensive too.

Introduction: What is a Lug Wrench?

A lug wrench is a type of wrench that is used to tighten and loosen the lug nuts on a car wheel. A lug wrench is one of the most common types of wrenches, and it can be found in almost any garage or toolbox. It is also known as a tire iron or tire spanner.

This type of wrench is made up of an L-shaped handle with a hexagonal socket at one end to fit over the head of the bolt, nut, or axle. The other end usually has a pin that fits into the slot in the center of the nut to hold it in place while turning.

Types of Lug Wrenches That You Can Buy

It is important to know the available types of lug wrenches. The most common types of lug wrenches are the standard type, the socket type, and the open-end type.

  • The standard type is a wrench with a closed loop at one end and an open loop at the other. The closed loop is used to tighten or loosen nuts, while the open loop can be used for either tightening or loosening nuts. This type of wrench is usually made from steel and has a chrome finish that protects it from rusting.
  • Socket types have a socket wrench with an opening on one side that fits over a nut or bolt head so it can be tightened or loosened. These come in various sizes for different-sized bolts and nuts. 
  • Open-end types have an opening at both ends which means they can be used for either tightening or loosening nuts and bolts.

As a rule of thumb, a breaker bar is used when the bolt head is large, and the nut or bolt has rounded corners. A torque wrench is used when rounding on the bolt head, and the nut or bolt is smaller. The torque wrench should be calibrated to help prevent over-tightening bolts that may cause breakage.

Why You Need A Lug Wrench To Start With

A lug wrench is a tool used on truck wheel nuts and bolts. It is mainly used to fasten and loosen the wheel nuts. The lug wrench has two ends. One end is a socket used to fasten and loosen the wheel nuts and bolts of trucks. The other end is a metal bar with a U-shaped opening that can be twisted to provide torque.

In this article, we will share with you some tips for Buying Lug Wrench

1. you must know the size of the lug nuts on your car before buying a wrench. The most common sizes are 14mm, 17mm, and 19mm.

2. You should always buy a lug wrench made of steel, not aluminum or plastic because they are less durable and can break easily.

3. Always buy a lug wrench from a reputable company like SARV because they have better quality products than other companies.

5Oct

Categories: Blog

Tire stitchers are necessary to effectively repair a tire. It is feasible for such an entire patch to cling to the tyre by using a tyre stitcher to ensure that it is compressed into the inner tube of the tyre. Specifications: Dimensions: 2″ x 1/4″

The top three tyre puncture repair techniques by far are:

  1. an outside fix made with tire string.
  2. an internal fix made using a patch.
  3. an internal fix utilising a patch and plug combo.

Another method to repair tire is Sewing the tire and for that we’ll need a good needle to sew the tire. A needle that is large enough to go through a tyre but not so large that it leaves large holes in the tyre is required.

The Standard Tire Repair Equipment

Pliers

It is a hand-hheld device that can be used to pull, chop, or securely grasp anything. Remove any foreign objects that have caused a tyre puncture, such as nails, rocks, or other pointed objects, with pliers.

Tool with a T-handle

There will be two T-handle tools: a rasp tool and a tool for inserting needles. They are employed to clean the hole and insert the plug securely.

The inside of the tyre hole needs to be cleaned using the rasp tool. Just move it up and down into the injured region. Next, place the repair plug in the needle insertion tool’s eye and insert it into the hole in nearly all of the affected areas. Wheel Plugs

These cordage fragments are used to seal off the injured area. You should keep an extra supply of plugs on hand in addition to the ones included with the kit.

The rubber cement

This type of glue is created by combining latex with a solvent, such as toluene, acetone, or heptane. The purpose of the tyre plug is to seal the leaky or punctured area.It creates a reliable yet adaptable relationship between two things.

Tire air pump

Solvents, which help the coatings stick to the rubber tyre, are among the three components of the pressurised fluid combination found in canned tyre inflators. sealants, which cover the hole momentarily. propellants that force the tire-inflating sealant into the container and into the tire. Auto Jack

Sometimes it’s impossible to fix the rupture without removing the tire. A car jack will be required in that situation.

How to patch a punctured tire:

There is no failsafe tire. Even items made by companies with the best bicycle or vehicle tyres might develop punctures. Therefore, a rupture repair kit should always be kept on hand as the first line of defence.

Now, stop and park your car on a level surface in case you come across a leak. Before beginning to repair the puncture, switch the engine off and engage the parking brake. Try to fix the tire while it’s still attached to the car. Take these actions:

  1. To remove the alien item that has pierced the tyre, use the pliers.
  2. Remove the item and replace it with the spiral probe. To clean and enlarge the leak’s area, slowly circle the spiral probe.
  3. Remove one tyre cord from the packet, then place it in the middle of the big needle that is given. Once both sides are level, push the strip through the needle eye.
  4. To unclog the puncture, lubricate these spiral probes with the rubberized cement solution and insert them there.
  5. Take out the spiral probe, then swiftly affix the needle and cord for repairing tires. Just enough of the cord should be visible outside the rubber after you’ve pushed it inside for a while.
  6. At this point, swiftly withdraw the insertion instrument by pulling the handle straight out.
  7. Trim the protruding ends of the cord with a blade or knife.Even if some pieces are not completely trimmed, the wheel will nonetheless flatten them.
  8. Your car is ready to depart once you re-inflate the punctured tyre.

What purpose does a stitching tool serve in tire repair?

Every vehicle’s puncture repair (patch) is done with a roller stitcher. The roll stitcher is used to forcefully roll over the surface of the patch to remove any potential tiny bubbles between the repair patch and the tyre.The equipment that is meant to mould or bend metallic coating into desired shapes is called a roller set or a rolling tool.

What exactly is an auto tire patch?

The auto tyre rupture patched bearings roller needle tool fits all types of tubes, tyres, and tubeless tyres exceptionally well and without causing any harm.The hole is patched from the inside. If the patch you have now is self-vulcanizing, once you start driving, it will heat up and melt into the tire’s rubber.